Differences

This shows you the differences between two versions of the page.

--- litespeed_wiki:lsmcd:installation [2017/10/26 14:08]
Lisa Clarke
+++ litespeed_wiki:lsmcd:installation [2019/11/27 14:34] (current)
Robert Perper [Centos / RHEL]
@@ Line 8: / Line 8: @@
 Run the following commands from an elevated shell terminal:
 <code>
-yum groupinstall “Development Tools”
+yum groupinstall "Development Tools"
-yum install autoconf automake zlib-devel openssl-devel expat-devel pcre-devel
+yum install autoconf automake zlib-devel openssl-devel expat-devel pcre-devel libmemcached-devel cyrus-sasl*
 </code>
@@ Line 15: / Line 15: @@
 Run the following commands from an elevated shell terminal:
 <code>
-apt-get install build-essential zlib1g-dev libexpat1-dev openssl
+sudo apt-get install git build-essential zlib1g-dev libexpat1-dev openssl libssl-dev libsasl2-dev libpcre3-dev -y
 </code>
@@ Line 29: / Line 29: @@
 <code>
 cd lsmcd
+./fixtimestamp.sh
 ./configure CFLAGS=" -O3" CXXFLAGS=" -O3"
 make
@@ Line 35: / Line 36: @@
 LSMCD should now be built. If there were any errors please double check that all package requirements were installed. If package requirements were not the issue, please post on our forums for further assistance.
-===== Install =====
+===== Install=====
 To install LSMCD after it has been compiled, run the following commands from the same elevated shell terminal:
+====Centos / RHEL====
 <code>
-make install
+sudo make install
 </code>
+====Debian/Ubuntu====
+<code>
+sudo make install
+sudo chown -R username /usr/local/lsmcd</code>
-That’s it! LSMCD should now be installed. Be sure to look into [[litespeed_wiki:lsmcd:configuration|configuring it]] next!
+LSMCD should now be installed.
+Now you will have to edit ''/usr/local/lsmcd/conf/node.conf'' to correctly set the IP address to bind.
+This is the example conf file for 127.0.0.1:11211 which is included in the release:
+<code>Repl.HeartBeatReq=30
+Repl.HeartBeatRetry=3000
+Repl.MaxTidPacket=2048000
+Repl.GzipStream=YES
+Repl.LbAddrs=127.0.0.1:12340
+Repl.ListenSvrAddr=127.0.0.1:12340
+REPL.DispatchAddr=127.0.0.1:5501
+RepldSockPath=/tmp/repld.usock
+CACHED.PRIADDR=127.0.0.1:11000
+CACHED.ADDR=127.0.0.1:11211
+#CACHED.ADDR=UDS:///tmp/lsmcd.sock
+#default is 8, it can be bigger depending on cache data amount
+Cached.Slices=8
+Cached.Slice.Priority.0=100
+Cached.Slice.Priority.1=100
+Cached.Slice.Priority.2=100
+Cached.Slice.Priority.3=100
+Cached.Slice.Priority.4=100
+Cached.Slice.Priority.5=100
+Cached.Slice.Priority.6=100
+Cached.Slice.Priority.7=100
+Cached.ShmDir=/dev/shm/lsmcd
+#If you change the UseSasl or DataByUser configuration options you need to remove the ShmDir folder and contents.
+#Cached.UseSasl=true
+#Cached.DataByUser=true
+#Cached.Anonymous=false
+#Cached.UserSize=1000
+#Cached.HashSize=500000
+#CACHED.MEMMAXSZ=0
+#CACHED.NOMEMFAIL=false
+##this is the global setting, no need to have per slice configuration.
+User=nobody
+Group=nobody
+#depends CPU core
+CachedProcCnt=4
+CachedSockPath=/tmp/cached.usock.
+#TmpDir=/tmp/lsmcd
+LogLevel=notice
+#LogLevel=dbg_medium
+LogFile=/tmp/lsmcd.log</code>
+If you wish to use SASL, remove the '#' comment from the line ''#Cached.UseSasl=true''
+===== Start =====
+There are various different ways to start/stop LSMCD. Here are just a few ways.
+==== Systemd ====
+<code>
+systemctl start lsmcd
+systemctl stop lsmcd
+systemctl enable lsmcd
+systemctl disable lsmcd
+</code>
+==== init.d ====
+<code>
+service lsmcd start
+service lsmcd stop
+chkconfig lsmcd on
+chkconfig lsmcd off
+</code>
+==== Manual ====
+<code>
+/usr/local/lsmcd/bin/lsmcdctrl start
+/usr/local/lsmcd/bin/lsmcdctrl stop
+</code>
+===== Test =====
+A quick way to test if LSMCD is running is to run the following from shell:
+<code>
+telnet 127.0.0.1 11211
+</code>
+Be sure to look into [[litespeed_wiki:lsmcd:configuration|configuring it]] next!