Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
litespeed_wiki:plesk:installation [2014/07/30 14:19] Michael Armstrong [Download the extension] |
litespeed_wiki:plesk:installation [2014/08/26 18:26] Michael Armstrong |
||
|---|---|---|---|
| Line 33: | Line 33: | ||
| {{litespeed_wiki:plesk:plesk_install_commands2.png?700}} | {{litespeed_wiki:plesk:plesk_install_commands2.png?700}} | ||
| + | |||
| + | **Note:** Plesk 11 users will also see a warning that ''/sbin/'' is not used when installing. This is normal and appears because the extension is compatible with both Plesk 11 and 12. | ||
| ===== Install LSWS from the Plesk Extension ===== | ===== Install LSWS from the Plesk Extension ===== | ||
| Line 54: | Line 56: | ||
| * Installation directory: Defines where LSWS will be installed. | * Installation directory: Defines where LSWS will be installed. | ||
| * Port offset: Allows running LSWS in parallel with Apache for testing purposes. The number in the port offset will be added to Apache port numbers to determine what port LSWS runs on. (For example, if the port offset is 1000, LSWS will serve sites on ports 1080 and 1443.) | * Port offset: Allows running LSWS in parallel with Apache for testing purposes. The number in the port offset will be added to Apache port numbers to determine what port LSWS runs on. (For example, if the port offset is 1000, LSWS will serve sites on ports 1080 and 1443.) | ||
| - | * Enable PHP suEXEC: Enables or disables suEXEC. suEXEC must be enabled through the LSWS settings if it is to be used. | + | * Enable PHP suEXEC: Enables or disables suEXEC. This setting must be enabled if you currently use suEXEC. |
| * Administrator email(s): Administrator emails. | * Administrator email(s): Administrator emails. | ||
| Line 67: | Line 69: | ||
| {{litespeed_wiki:plesk:plesk_start_lsws.png?700}} | {{litespeed_wiki:plesk:plesk_start_lsws.png?700}} | ||
| - | ==== Build PHP for LSWS ==== | + | ==== Get PHP for LSWS ==== |
| - | LSWS requires PHP built with LSAPI. We will be building PHP through the WebAdmin console, but PHP can also be built through the command line. (When building from the command line, simply add the %%"--with-litespeed"%% option to have it built with LSAPI.) | + | LSWS requires PHP built with LSAPI. There are a number of ways to do this. Many Plesk users may find it easiest to get PHP for LSWS through the [[http://rpms.famillecollet.com/|Remi Repository]]. You can also build PHP through the WebAdmin console (detailed below) or through the command line. (When building from the command line, simply add the %%"--with-litespeed"%% option to have it built with LSAPI.) |
| Access the WebAdmin console by clicking "WebAdmin Console". | Access the WebAdmin console by clicking "WebAdmin Console". | ||
| Line 106: | Line 108: | ||
| ==== Test your sites with a port offset ==== | ==== Test your sites with a port offset ==== | ||
| + | |||
| The beauty of the port offset is that you can run LSWS and Apache in parallel. This means you can try out your sites with LSWS to make sure they work before atually turning off Apache. In our setup, I have set the port offset to 1000. If I want to check any sites, I can do so on ports 1080 and 1443. | The beauty of the port offset is that you can run LSWS and Apache in parallel. This means you can try out your sites with LSWS to make sure they work before atually turning off Apache. In our setup, I have set the port offset to 1000. If I want to check any sites, I can do so on ports 1080 and 1443. | ||
| Line 120: | Line 123: | ||
| {{litespeed_wiki:plesk:plesk_lsws_running.png?700}} | {{litespeed_wiki:plesk:plesk_lsws_running.png?700}} | ||
| - | |||